Skip to content
WW2 Information

Searchsoon

FM 101-10 Staff Officers Field Manual Organization Technical Logistical Data (1941), p. 101

Page 101 of 363 in FM 101-10

Transcription

TROOP MOVEMENTS (13) Minimum Requirements for Securing Four Wheel Trucks and Passenger Cars, (Single or Dual Wheels).—Flat, or Drop End Gondola Cars. See Fig. 9. Item A B C D No. of PCS. F G 8with Items "D" 4withItems "F" 4 16 4 Required for passenger cars only Description. Brake wheel clearance. See Fig. 6. VACANT. VACANT. 6 in. x 8 in. x 24 in. blocks, (pattern 3). Height at point of contact with tire must be not less than 4 in. from car floor. Locate in front and rear of outside wheels. Nail heel of block to car floor with three 40-D nails and toe-nail that portion under tire to car floor with two 40-D nails before Items "E" are ap plied. Not required when Items "F" and "G" are used. 2 in. x 4 in. x 36 in. cleats, (pattern 2). Nail lower piece to car floor with three 40-D nails and top piece to the one below with three 40-D nails. May be nailed tp top of Items "F", if used, in which case only ona is required at each location. 6 in. x 8 in. timbers, (pattern 4), length not less than overall width of vehicle at car floor, chamfered 2 in. at point of contact with tires. Apply as shown in sketch 2 and secure to prevent displacement. Not required when Items "D" are used. 2 in. x 4 in. x 12 in. cleats, (pattern 1). Locate against Items "F", lengthwise of car, at center line of tire. Nail lower piece to car floor with three 40-D nails and top piece to the one below with three 40-D nails. Not required when Items "D" are used. 4 strands, 2 wrappings, No. 8 Ga. black annealed wire. Pass through spokes, or holes in disc wheels and through stake pockets, tightening only enough to remove slack. Not required when loaded in gon dola cars. 2 in. x 4 in. x 36 in. cleats, (pattern 2), nailed to floor, lengthwise of car, with six 40 -D nails. K 4 4 strands, 2 wrappings, No. 8 Ga. black annealedRequired for wire. Pass underneath Items "J", and over top ofpassenger bumper spring. After passenger car springs havecars only been compressed as much as possible, bring both endsof wire together and twist tie with rod or bolt. Seesketch 3. Brakes must be applied. See General Rules for further details. 96

Uncorrected OCR text. Columns and tables may be out of order; the scan is the authority.

Original scan

Loading the original scan…
Original scan, PDF page 101. Only this page is downloaded. Open the full PDF

FM 101-10 Staff Officers Field Manual Organization Technical Logistical Data, PDF page 101

100%

Data on this page

9 data points

AttributeValue
Securing 4-wheel trucks and passenger cars on flat or drop-end gondola rail cars
min height of blocking at tire contact4 in“Height at point of contact with tire must be not less than 4 in. from car floor.”
Securing vehicles on rail cars, pattern 3 blocks
block size6 in. x 8 in. x 24 in.“6 in. x 8 in. x 24 in. blocks, (pattern 3)”
Securing vehicles on rail cars, pattern 2 cleats
cleat size2 in. x 4 in. x 36 in.“2 in. x 4 in. x 36 in. cleats, (pattern 2)”
Securing vehicles on rail cars, pattern 4 timbers
timber size6 in. x 8 in.“6 in. x 8 in. timbers, (pattern 4)”
Securing vehicles on rail cars, pattern 1 cleats
cleat size2 in. x 4 in. x 12 in.“2 in. x 4 in. x 12 in. cleats, (pattern 1)”
Securing vehicles on rail cars, lashing wire
number of strands4 strands“4 strands, 2 wrappings, No. 8 Ga. black annealed wire.”
Securing vehicles on rail cars, heel blocks nailing
nails per heel-block to car floorthree“Nail heel of block to car floor with three 40-D nails”
Securing vehicles on rail cars, toe-nailing of block under tire
nails per toe-nail to car floortwo“toe-nail that portion under tire to car floor with two 40-D nails”
Securing 4-wheel trucks on rail cars, Item D blocks
pieces required (with Items F absent)8 pieces“8with Items "D"”

Extracted from this page by machine. Each row quotes the text it came from; check it against the scan.