Skip to content
WW2 Information

Searchsoon

FM 101-10 Staff Officers Field Manual Organization Technical Logistical Data (1941), p. 99

Page 99 of 363 in FM 101-10

Transcription

45 TROOP MOVEMENTS (12) Minimum Requirements for Securing Half Tracks.— Flat, or Drop End Gondola Cai\s. See Fig. 8. Item No. of PCS. Description. A Brake wheel clearance. See Fig. 6. B 4 6 in. x 8 in. x 24 in. blocks, (pattern 3), cut to fit con tour of crawler tread. Nail heel of block to car floor with five 40-D nails and toe-nail that; portion under crawler tread to car floor wiith two 40-D nails. Not required when Items "F" and "G" are used. C 2 2 in. x 4 in. x 36 in. cleats, (pattern 2). Nail to car floor with three 40-D nails. D 4 6 in. x 8 in. x 24 in. blocks, (pattern 3). Height atpoint of contact with tire must be not less than 4 in. from car ffoor. Locate in front and rear of wheels. Nail heel of block to car floor with three 40-D nails and toe-nail that portion under tire to car floor with two 40-D nails before Items "E" are applied. Not required when Items "F" and "G" are used. E 4 2 in. x 4 in. x 36 in. cleats, (pattern 2). Nail lower with piece to car floor with three 40-D nails and top piece Items "D" to the one below with three 40-D nails. May be 2 nailed to top of Items "F", if used, in which case with only one is required at each location. Items "F" F 4 6 in. x 8 in. timbers, (pattern 4), length not less thanoverall width of vehicle at car floor, chamfered 2 in. at point of contact with tires and crawler treads. Apply as shown in sketch 2 and .secure to prevent displacement. Not required when Items "B" and "D" are used. G 16 2 in. x 4 in. x 12 in. cleats, (pattern 1. Locate againstItems "F", lengthwise of car, at center line of tire or crawler tread. Nail lower piece to car floor with three 40-D nails and top piece to the one below with three 40-D nails. Not required when Items "B" and "D" are used. H 44 strands, 2 wrappings, No. 8 Ga. black annealedw_ire. Pass front wires through spokes, or holes in disc wheels and through stake pockets. Pass rear wires between equalizer and gudeon (above springs) and attach to nearest stake pocket. Tighten all wires only enough to remove slack. Not required when loaded in gondola cars. Brakes must be applied. See General Rules for further details. 94

Uncorrected OCR text. Columns and tables may be out of order; the scan is the authority.

Original scan

Loading the original scan…
Original scan, PDF page 99. Only this page is downloaded. Open the full PDF

FM 101-10 Staff Officers Field Manual Organization Technical Logistical Data, PDF page 99

100%

Data on this page

6 data points

AttributeValue
Half-track securing, blocks 6x8x24
blocks required4 blocks“4 6 in. x 8 in. x 24 in. blocks”
Half-track securing, cleats 2x4x36
cleats required2 cleats“2 2 in. x 4 in. x 36 in. cleats”
Half-track securing, tire blocks
minimum height at contact point4 inches“not less than 4 in. from”
Half-track securing, cleats 2x4x12
cleats required16 cleats“16 2 in. x 4 in. x 12 in. cleats”
Half-track securing, timbers
timbers required4 timbers“4 6 in. x 8 in. timbers”
Half-track securing wire
strands (OCR reads 44)44 strands“44 strands, 2 wrappings, No. 8 Ga. black”

Extracted from this page by machine. Each row quotes the text it came from; check it against the scan.