Skip to content
WW2 Information

Searchsoon

German Infantry Weapons (Special Series) (1943), p. 146

Page 146 of 203 in German Infantry Weapons (Special Series)

Transcription

ANTITANK GUJNS AND INFANTRY HOWITZERS 133 grooves, which are cut in the plunger, graduate the control. The piston-rod stuffing box is packed with soft packings. Normal recoil is 700 mm (27.56 inches); metal to metal, 730 mm (28.74 inches). The recoil cylinder should, according to German instructions, be filled until the oil gauge on the near edge protrudes 44 mm (13/4 inches). The safety plunger in the breechblock has a cutaway portion to engage the firing shaft. When the breech is properly closed, the plunger can enter its recess in the bottom of the breech ring. To open the breech (by hand): First, set the semi-automatic plunger to AUS ("out"). The firing pin has been recocked during recoil. When the breech-mechanism lever is pulled to the right rear, the crank is actuated, forcing the sliding block to the left and thereby opening the breech. The extractors eject the cartridge case and retain the breechblock in the fully open position. To close the breech (by hand): Release the extractors by loading a cartridge or actuating the extractor releasing lever. The breech should close automatically. To open the breech (semi-autoila tie): Set the spring-plunger to semi- automatic. The word EIN ("in") will then show upwards. On recoil a stop fitted to the cradle overrides the piston catch. On run-out, the stop and front face of the piston catch engage, forcing the piston to the rear and com- pressing the inner and outer springs, until the piston catch is forced inward and the outer spring reasserts itself. The piston with the rack spindle then moves forward under the action of the outer spring, the rack engages the breech-mechanism lever pinion, revolves it, and rotates the breech-mechan- ism lever to the right rear, so opening the breech. To close the breech (semi-automatic): Release the extractors by loading a cartridge. The inner spring then asserts itself, allowing the rack spindle to move forward and rotate the pinion and breech-mechanism lever to the closed position. To fire: The firing plunger is forced upward by a lever on the carriage, which engages the firing lever and rotates it. The firing pin is held cocked by the firing shaft, and is released when the cutaway portion on it is opposite the front shoulded on the firing pin, thus firing the round. The recocking process follows on recoil.) 524652°--3----10

Uncorrected OCR text. Columns and tables may be out of order; the scan is the authority.

Original scan

Loading the original scan…
Original scan, PDF page 146. Only this page is downloaded. Open the full PDF

German Infantry Weapons (Special Series), PDF page 146

100%

Data on this page

8 data points

AttributeValue
5-cm Pak 38 antitank gun
normal recoil length700 mm“Normal recoil is 700 mm (27.56 inches); metal to metal, 730 mm (28.74 inches).”
metal-to-metal recoil length730 mm“Normal recoil is 700 mm (27.56 inches); metal to metal, 730 mm (28.74 inches).”
5-cm Pak 38 antitank gun recoil cylinder
oil gauge protrusion when filled44 mm“protrudes 44 mm (13/4 inches)”
5-cm Pak recoil system
normal recoil700 mm“packings. Normal recoil is 700 mm (27.56 inches);”
normal recoil27.56 inches“packings. Normal recoil is 700 mm (27.56 inches);”
metal-to-metal recoil730 mm“metal to metal, 730 mm (28.74 inches).”
metal-to-metal recoil28.74 inches“metal to metal, 730 mm (28.74 inches).”
5-cm Pak recoil cylinder
oil gauge protrusion when filled44 mm“44 mm (13/4 inches).”

Extracted from this page by machine. Each row quotes the text it came from; check it against the scan.